Type and density of liquid Essay Example for Free

Type and density of liquid state EssayThese are the variables that I could choose to tenseness on. I have chosen to focus and adapt on the idea of insulation. Prediction I divine that the more insulation (layers) there is, the smaller the reduction in heat. I think this because when the outside disperse tries to touch the container to cool it, it bequeath be stopped by the insulation, so it will take long- playing to cool. Also, when heat tries to escape from the container, it will go into the first layer of insulation, which will thusly absorb the heat. It would then still keep the container warm, not letting as much heat out as fast.I also predict that if I have a lid it will take even thirster to cool, because, as you can see in the picture below, evaporation will also take place. If I have a lid, the heat will then be stopped from escaping into the air through the top. As shown below- Equipment Timer- this is to time the amount of money of time the liquid is in the container. This will limit positive(predicate) that the time will be the same for apiece experiment. Data logger and Thermometer- this is to take the temperature of the water. I will use cardinal forms of identifying the temperature. This way I can compare the two results and see if there are any forceful differences.Also, a datalogger is accurate, but I will still use a thermometer to back up my results. detachment Material- I am pass to use a spark type material as my insulation. Clamp- I will use a clamp to hold both the datalogger and thermometer above the container. Container- I am going to use a glass beaker to hold the liquid. I am apply this instead of a polystyrene loving cup, because the cup would hold residue heat, which would affect our results. Also a polystyrene cup is already quite insulated. * Kettle- this is to heat the liquid before I put it in the container.I will clean out the kettledrum, to compensate sure there is no bleak, therefore the heat will b e reflected back into the kettle, instead off creation absorbed. This should help it to r separately its highest temperature. I will make sure that there is 1litre of water in the kettle each time put it on to boil. Measuring Apparatus- I will put the water instantaneously into the glass beaker, measuring it in there. Lid- To put over the glass beaker to try and prevent evaporation. Fair test and Other Factors that need to be restrainled There are things that I will need to try and make sure are the same throughout my experiment.These are Amount of liquid- I will have to make sure that each time I refill the glass beaker I have the same amount of liquid. To do this I will measure it in some measuring apparatus. Each time I will use the same type and size of measuring apparatus, for the same accuracy. To make this even fairer I will simply measure the amount of water in my glass beaker, so I contend that it will always be the same. Temperature of surroundings- there is not much I can do to control this, but to make sure there is no drastic change, I will stay away(p) from radiators and places in direct sunlight.Shape, Colour, Size, Surface Area and Thickness of container- will have to be the same throughout my experiment to keep it fair and to get reliable results. For instance, if I had a different colour container each time I did my experiment it would affect my results. This would be, because instead of reflecting the heat back in, if I had a black container it would absorb the heat. To make sure of this I will use the same container each time. Temperature of liquid to start- I will try to keep the around the same. If I cannot keep the temperature the same I will bonnie measure the difference between the two (start and end).Type and Density of Liquid- I will keep using the same type of liquid throughout my experiment because some types may loose heat at a different rate than others. I will use water because it is easily available, and it is the same each time. Surface container is on- will have to be the same. If for example I was to put it on a foam surface one day, and something different another day, it would affect how much heat is lost. This is due to the surface acting as insulation. Lid- I am going to use a lid each time. This should stop a lot of heat reduction through evaporation, which I have already explained in my prediction.